The load on the coupling device is 10600 kg
The load on the axial unit is 24,000 kg
The allowed gross weight is 34600 kg
The net weight of the semi-trailer is 7100 kg
The technically permissible load capacity is 27,500 kg
Wheelbase 6380 mm
Center-to-center distance 1320 mm
Center-to-center distance 1320 mm
The distance between the springs is 1200 mm
Wheel track 2040 mm
Overall length 13790 mm
Overall width 2550 mm
The inner length in light is 13520 mm
The inner width in the light is 2440 mm
Internal height 660 mm
Platform volume is 21.8 m3
Platform area 33 m2
Loading height of the platform is 1380 mm
Loading height of the platform (with lowered pneumatic cylinders, 120mm) 1260 mm
Front overhang 1840 mm
The radius of the front overhang is 20-40 mm
Rear turning radius 2300 mm
The height of the frame above the hitch is 176 mm
The height of the coupling device of a horizontally standing unloaded semi-trailer is 1200-1250 mm

Technical Description:
Frame
The semi-trailer frame is welded, the spars are of I-beam cross section, variable in height and interconnected by crossbars. Rear protection and side protection are attached to the frame (they are installed when delivered to countries where the installation of protective devices is mandatory). The coupling pin is of class H50 in accordance with the requirements of UNECE Regulation No. 55 and is designed for operation with a tractor unit having a class G50 coupling device in accordance with the requirements of UNECE Regulation No. 55.

Pendant
Tubular cross-section axles with a drum brake mechanism. The suspension is pneumatic "MAZ" with a ride height of FH = 360 mm.

Pneumatic brakes
The pneumatic, two-wire service brake system is equipped with TEBS, consists of connecting heads, trunk filters, a trailer release valve with a built-in distributor, receivers with condensate drain valves, control outlet valves, an EBS modulator, and brake chambers. Parking brake system with brake chambers with energy accumulators on the second and third axles.

Air suspension
The air suspension includes 1 crane for lifting/ lowering, which is mounted on the rear left in the direction of travel, ABS from the company "WABCO", F. "Knorr-Bremse".

ABS electrical equipment.
ABS system configuration (2S/2M). Connection to the tractor's power supply system via a cable with an ISO 7638 connector. ABS sensors are installed on the second axis. TEBS produced by F. "Wabco", F. "Knorr-Bremse".

Tires
Tires 385/65R22.5 from Matador or CIS. Fastening with standard bolts and nuts, the hole diameter is 26 mm.

Body and chassis
Sliding support device of the OZAA company with a mechanical drive, permissible load of 24 tons, control on one side, on the right in the direction of movement.
Installation of splash-proof mudguards.
2 anti-rollback stops with holders.
Side protection according to UNECE Regulation No. 73
Basket holder for one spare wheel, mounting at the rear of the axial unit on the right.
A plastic tool box measuring 1184x320x500, mounted in the direction of travel to the right in front of the axial unit, as required by the consumer.
Installation of the fuel tank V=340 liters.
Steel protection against rear entry according to UNECE Regulation No. 58

Flooring
The floor consists of laminated waterproof plywood (panels) with a thickness of 27 mm. The sheets are located between the longitudinal beams and the outer frame. The end surfaces and seams between the panels are sealed, and the plywood surface is mesh-coated.

Front wall
The front side is steel with a height of 660 mm, with angular metal posts bolted to the frame.

Back wall
Folding side rear (steel) "MAZ" with S-shaped sliding locks.
Metal posts are bolted to the edge of the frame.

Side walls
4 pairs of folding sides "MAZ" with S-shaped sliding locks.
3 pairs of folding MAZ racks.
Steel outer frame with 12 pairs of rings for fixing the load, welded rings, additional load of 2000 kg per ring, 3 pairs of pockets for folding MAZ racks.

Flatbed and platform semi-trailers