Sale of timber trailers in Ulyanovsk

Three-axle sorting trailer with swivel drawbar, model AH-342
A popular model of a sorting truck designed for the harsh conditions of Siberia.The AH-342 model features a specially designed design for use in the Siberian region. The trailer on a spring suspension is designed for harsh conditions. Reinforced suspension, special wing design, protection of electrical and pneumatic wiring from mechanical damage - all this in order to maximize the service life of the equipment. The reinforced drawbar ensures the reliability of the trailer and distinguishes the model from competitors.
...

The machine is designed for collecting, loading, transporting through logging areas and portages of sorts, as well as unloading, sorting and storing them. The use of the machine is effective on soils with medium and high bearing capacity.
Manufacturer: JSC "Minsk Tractor Plant"
...

The sliding floor consists of a series of longitudinal aluminum beams that are hydraulically driven. The drive is three-section. Each section of the beams is powered by its own hydraulic cylinder. The beams perform reciprocating movements in the longitudinal direction. During unloading and loading, all sections of the beams move simultaneously (the beam stroke is 200 mm.). When the beams are reversed, the sections move alternately. Then the cycles repeat and the load moves. The time of full unloading is 15 minutes.

There is no risk of the semi-trailer tipping over during unloading, in comparison with semi-trailers with dump truck lifting. Loading and unloading takes place horizontally, relative irregularities are not dangerous, as well as unstable soils of unloading sites. Unloading can be carried out in rooms with a ceiling height not much higher than the actual semi-trailer (low warehouses, factory workshops, docks). Full control of the hydraulic structure from a manual remote control panel. The design of the sliding floor does not require any routine technical support during operation. The ability to load and unload without using a loader inside the body....

The sliding floor consists of a series of longitudinal aluminum beams that are hydraulically driven. The drive is three-section. Each section of the beams is powered by its own hydraulic cylinder. The beams perform reciprocating movements in the longitudinal direction. During unloading and loading, all sections of the beams move simultaneously (the beam stroke is 200 mm.). When the beams are reversed, the sections move alternately. Then the cycles repeat and the load moves. The time of full unloading is 15 minutes.

There is no risk of the semi-trailer tipping over during unloading, in comparison with semi-trailers with dump truck lifting. Loading and unloading takes place horizontally, relative irregularities are not dangerous, as well as unstable soils of unloading sites. Unloading can be carried out in rooms with a ceiling height not much higher than the actual semi-trailer (low warehouses, factory workshops, docks). Full control of the hydraulic structure from a manual remote control. The design of the sliding floor does not require any routine technical support during operation. The ability to load and unload without using a loader inside the body....

The sliding floor consists of a series of longitudinal aluminum beams that are hydraulically driven. The drive is three-section. Each section of the beams is powered by its own hydraulic cylinder. The beams perform reciprocating movements in the longitudinal direction. During unloading and loading, all sections of the beams move simultaneously (the beam stroke is 200 mm.). When the beams are reversed, the sections move alternately. Then the cycles repeat and the load moves. The time of full unloading is 15 minutes.

No risk of overturning of the semi-trailer during unloading, in comparison with semi-trailers with dump truck lifting. Loading and unloading takes place horizontally, relative irregularities are not dangerous, as well as unstable soils of unloading sites. Unloading can be carried out in rooms with a ceiling height not much higher than the actual semi-trailer (low warehouses, factory workshops, docks). Full control of the hydraulic structure from a manual remote control panel. The design of the sliding floor does not require any routine technical support during operation. The ability to load and unload without using a loader inside the body....

Non–mileage logging truck based on FAW J6 CA3250 truck with CA6DL2-37E5 engine, EURO 5 Transmission: manual, 12-speed, synchronized, with demultiplier.

Description of the model ...

Three-axle woodchip semi-trailer, SP-345 with a body volume of 120 m3
Updated SP-345 three-axle woodchip semi-trailer with a record body volume of 120 m3! The trailer's load capacity is 29 tons. Like all products from Meusburger Novtrak, the semi-trailer is equipped with modern systems!
...

Weight of the transported cargo, kg - 50,000
Curb weight of the semi-trailer, kg - 12,300
The total weight of the semi-trailer, kg is 62,300 ...

Weight of the transported cargo, kg - 50,000
Weight of the loaded semi-trailer, kg - 12000
The total weight of the semi-trailer, kg is 62,000 ...

Loading range (cross-section) 1.5 m2
Overall width 2.33 m
Total length 4.87 m ...

Loading range (cross-section) 2.5 m2
Overall width 2.56 m
Total length 5.6 - 6.6 m ...

Loading range (cross-section) 2.5 m2
Overall width 2.47 m
Total length ...

Loading range (cross-section) 2.5 m2
Overall width 2.4 m
Total length 6.2 m - 7.6 m ...

Engine:
Type 3 Standard: Caterpillar C9 Acert 261 kW (350 hp)
water-cooled diesel engine ...

Volume

63 m3 ...

The load capacity is 10 tons.YAMZ-6565 Euro-4 engine, Ural 55571 chassis, tires:ID-P284 Analog 596009

The price includes VAT. Under the order. Free shipping. It does not require investments. Serviced by an official dealer. Possible sale on lease. Ready for operation.

Undercarriage: wheeled
In good condition. Under the order. The price includes VAT. Free shipping. It does not require investments. Possible sale on lease.

Undercarriage: wheeled
In good condition. The engine is uncomplicated. The price includes VAT. It does not require investments. Serviced by an official dealer. Under the order. Possible sale on lease. Ready for operation. I'll help with the delivery.

Capacity: 170-450 t/h
Hopper capacity: 6m3
Maximum size of the uploaded material: 700 mm ...

Capacity - 200-500 t/h
The size of the loaded material is 600 mm
The size of the screening surface is mm 5000*1500 ...

• Crushing method: Jaw
• Design: Self-propelled tracked
• Capacity, t/h: 180-400 ...

Capacity - 50-100t/hour 
The volume of the hopper is m3 4
The maximum size of the loaded material is 450mm.  ...

Max. loading size, mm - 600
Length * Width of the feeder, mm - 4500×2200
Productivity, t/h - 200-500 ...

• Crushing Method: Rotary
• Design: Self-propelled tracked
• Capacity, t/h: 150-230 ...