Sale of new chip semi-trailers in Vladimir

Three-axle woodchip semi-trailer, SP-345 with a body volume of 120 m3
Updated SP-345 three-axle woodchip semi-trailer with a record body volume of 120 m3! The trailer's load capacity is 29 tons. Like all products from Meusburger Novtrak, the semi-trailer is equipped with modern systems!
...

SP-368 three-axle woodchip semi-trailer
The durable steel profiled body allows you to transport a wide variety of loads! New technologies in the production of our woodchip trucks make operation more convenient and easier!
The three-axle woodchip semi-trailer is designed to transport various cargoes, both bulk and packaged. ...

Loading range (cross-section) 1.5 m2
Overall width 2.33 m
Total length 4.87 m ...

The sliding floor consists of a series of longitudinal aluminum beams that are hydraulically driven. The drive is three-section. Each section of the beams is powered by its own hydraulic cylinder. The beams perform reciprocating movements in the longitudinal direction. During unloading and loading, all sections of the beams move simultaneously (the beam stroke is 200 mm.). When the beams are reversed, the sections move alternately. Then the cycles repeat and the load moves. The time of full unloading is 15 minutes.

There is no risk of the semi-trailer tipping over during unloading, in comparison with semi-trailers with dump truck lifting. Loading and unloading takes place horizontally, relative irregularities are not dangerous, as well as unstable soils of unloading sites. Unloading can be carried out in rooms with a ceiling height not much higher than the actual semi-trailer (low warehouses, factory workshops, docks). Full control of the hydraulic structure from a manual remote control panel. The design of the sliding floor does not require any routine technical support during operation. The ability to load and unload without using a loader inside the body....

The sliding floor consists of a series of longitudinal aluminum beams that are hydraulically driven. The drive is three-section. Each section of the beams is powered by its own hydraulic cylinder. The beams perform reciprocating movements in the longitudinal direction. During unloading and loading, all sections of the beams move simultaneously (the beam stroke is 200 mm.). When the beams are reversed, the sections move alternately. Then the cycles repeat and the load moves. The time of full unloading is 15 minutes.

There is no risk of the semi-trailer tipping over during unloading, in comparison with semi-trailers with dump truck lifting. Loading and unloading takes place horizontally, relative irregularities are not dangerous, as well as unstable soils of unloading sites. Unloading can be carried out in rooms with a ceiling height not much higher than the actual semi-trailer (low warehouses, factory workshops, docks). Full control of the hydraulic structure from a manual remote control. The design of the sliding floor does not require any routine technical support during operation. The ability to load and unload without using a loader inside the body....

The sliding floor consists of a series of longitudinal aluminum beams that are hydraulically driven. The drive is three-section. Each section of the beams is powered by its own hydraulic cylinder. The beams perform reciprocating movements in the longitudinal direction. During unloading and loading, all sections of the beams move simultaneously (the beam stroke is 200 mm.). When the beams are reversed, the sections move alternately. Then the cycles repeat and the load moves. The time of full unloading is 15 minutes.

No risk of overturning of the semi-trailer during unloading, in comparison with semi-trailers with dump truck lifting. Loading and unloading takes place horizontally, relative irregularities are not dangerous, as well as unstable soils of unloading sites. Unloading can be carried out in rooms with a ceiling height not much higher than the actual semi-trailer (low warehouses, factory workshops, docks). Full control of the hydraulic structure from a manual remote control panel. The design of the sliding floor does not require any routine technical support during operation. The ability to load and unload without using a loader inside the body....

Non–mileage logging truck based on FAW J6 CA3250 truck with CA6DL2-37E5 engine, EURO 5 Transmission: manual, 12-speed, synchronized, with demultiplier.

Description of the model ...

Three-axle sorting trailer with swivel drawbar, model AH-342
A popular model of a sorting truck designed for the harsh conditions of Siberia.The AH-342 model features a specially designed design for use in the Siberian region. The trailer on a spring suspension is designed for harsh conditions. Reinforced suspension, special wing design, protection of electrical and pneumatic wiring from mechanical damage - all this in order to maximize the service life of the equipment. The reinforced drawbar ensures the reliability of the trailer and distinguishes the model from competitors.
...

Weight of the transported cargo, kg - 50,000
Curb weight of the semi-trailer, kg - 12,300
The total weight of the semi-trailer, kg is 62,300 ...

Weight of the transported cargo, kg - 50,000
Weight of the loaded semi-trailer, kg - 12000
The total weight of the semi-trailer, kg is 62,000 ...

Dump truck on a JAC N120 truck from the GEF Automobile Plant (chaika-service).

The car is equipped with a dump truck body, "scoop" configuration, tilt angle up to 50 degrees, capacity up to 10 m3. ...

The JAC N90 is one of the most modern representatives of the line of medium–tonnage commercial trucks. The total weight of the car is 9,030 kg, it is very maneuverable and can carry goods over short, medium and long distances. The model has been specially adapted for Russian working conditions.

The JAC N90 is equipped with a modern cabin with an ergonomic interior, designed for three people. ...

The JAC N350 concrete mixer truck with a 6x4 wheel formula and an allowable gross weight of 35 tons is designed to deliver concrete mix and/or prepare it en route or upon arrival at the concreting site. The dimensions of the car are 9720x2550x3960 mm, the wheelbase is 4100 +1350 mm. The weight of the vehicle in running order is 15030 kg.

A Chinese-made mixing drum with a capacity of 10 cubic meters is installed on the JAC N350 chassis. The drum is installed at an angle of 12 degrees and is equipped with a 400 liter water tank. The loading/unloading speed is 2.7/0.65 cubic meters/min. ...

The JAC K7 is a high–tech tractor truck designed for transporting various types of goods over long distances. The car can be used in a wide variety of industries, from construction and industry to agriculture and retail.

The 4x2 wheel formula and the distance between the axles of 3,900 mm ensure compact dimensions. With a curb weight of 7568 kg, the JAC K7 can operate as part of a road train with a gross weight of up to 45 tons. The car is powered by a powerful 6-cylinder engine with a volume of 11.8 liters, which develops 488 hp and 2,030 Nm of torque. ...

Undercarriage: wheeled
In good condition. The engine is uncomplicated. The price includes VAT. It does not require investments. Serviced by an official dealer. Under the order. Possible sale on lease. Ready for operation. I'll help with the delivery.

Loading range (cross-section) 2.5 m2
Overall width 2.56 m
Total length 5.6 - 6.6 m ...

Loading range (cross-section) 2.5 m2
Overall width 2.47 m
Total length ...

Loading range (cross-section) 2.5 m2
Overall width 2.4 m
Total length 6.2 m - 7.6 m ...

Specifications
Power hp 75(102)
Load capacity, t 1.5/3.1 ...

Specifications:

Overall length, mm 6260 ...

The machine is designed for collecting, loading, transporting through logging areas and portages of sorts, as well as unloading, sorting and storing them. The use of the machine is effective on soils with medium and high bearing capacity.
Manufacturer: JSC "Minsk Tractor Plant"
...

Volume

63 m3 ...

The load capacity is 10 tons.YAMZ-6565 Euro-4 engine, Ural 55571 chassis, tires:ID-P284 Analog 596009

The price includes VAT. Under the order. Free shipping. It does not require investments. Serviced by an official dealer. Possible sale on lease. Ready for operation.

Undercarriage: wheeled
In good condition. Under the order. The price includes VAT. Free shipping. It does not require investments. Possible sale on lease.