Name of the characteristic or parameter
The value of a characteristic or parameter
Mileage during the warranty period, km
100 000
Make and model of the engine
Weichai Power WP 12.460E50, Environmental class 5
Net power, kW/hp
333/460
Maximum torque, NM
2 110 (2 150)
Engine displacement, cm3
11 596
Engine fuel supply system
500 L fuel tank, fuel lines, coarse and fine filters. The fuel supply is controlled by an electronic unit. The electronic engine block also implements the function of a speed limit device.
Engine air supply system
Dry type air filter, air ducts
The release system
Engine brake, pipes, exhaust muffler-neutralizer with toxic substances suppression system (SCR)
Engine start-up device
Installed
Preheating system
The liquid heater is installed depending on the climatic design of the car and makes it easier to start the engine at subzero ambient temperatures, and can also automatically maintain the thermal state of the idle engine and cabin air.
Make and model of gearbox
Allison 4000
Number of gears
6 forward gears; 1 reverse gear
Gear ratios

gear number
I
II
III
IV
V
VI
R1
gear ratio
3,51
1,91
1,43
1,00
0,74
0,64
4,00
Gimbal transmission
It consists of five cardan shafts
Transfer case
Mechanical, two-speed, differential, three-shaft, with forward and reverse torque distribution of 1:2,696, with permanent axle drive. The transfer case is controlled remotely, electropneumatically from the driver's cabin. Gear ratio 0.89 and 1.536
Driving axle /
Driving axles
The first, second, third and fourth axles are driving, two–stage, with a central gearbox and wheel gears.
The first and second axes are controllable, with hinges of equal angular velocities.
The first axle has an inter-wheel differential lock.
The second axle is equipped with anti-lock braking system (ABS) sensors.
Third axle with inter-wheel and inter-axle differential lock.
Fourth axle with inter-wheel differential lock, equipped with ABS sensors
Gear ratio
5.08 (5.14 – for oblique planetary gear)
Controlled axis /
controlled axes
First and second axes
Pendant
The front (on the first and second axles) is spring–loaded, on low–leaf springs with silent blocks, with lateral stability stabilizers and hydraulic shock absorbers of a telescopic type; The rear is spring-balanced, multi-leaf, with a lateral stability stabilizer on the rear axle, with V-shaped upper jet rods
Wheels
Disk sizes 8.5-24
Tires
Pneumatic, dimensions 12.00R24
Steering control
The steering is dual–circuit. The steering mechanism is integral type. The steering column is adjustable in height and tilt, equipped with injury-proof and anti-theft devices.
The braking system
Pneumatic, dual-circuit, with separate drive of the front and rear wheels. It is equipped with ABS and traction control system.Drum-type wheel brakes.The parking brake system acts on the wheels of the rear and middle axles driven by spring-loaded energy accumulators. The drive of spring energy accumulators is pneumatic.The function of the backup braking system is performed by the parking brake or the serviceable circuit of the service braking system. Auxiliary – compression type with a flap on the engine turbocharger nozzle, electropneumatic drive, cabin control
Freewheel brakes applied
From 16 to 23 mm
Electrical equipment
The electrical system is DC with a rated voltage of 24 V. The "negative" terminal of the batteries is connected to the mass of the car (frame, engine, switching unit). The "plus" battery terminal is connected to the vehicle's on-board system via a battery switch. Electrical equipment includes lighting and light-signalling devices, devices and electronic equipment that ensure the functioning of the vehicle and its components
The cabin
Small type 6418 with updated interior, double, with spring suspension
Note – The value in parentheses is for an increased technically permissible maximum weight of 54,000 kg.
Heating system
Liquid type from the engine cooling system or independent liquid heater; independent air heater – on request
Frame
Ladder type made of stamped, die-welded and cast parts connected by self-locking fasteners and rivets
Side protection device
Installed
Rear safety device
Installed
Loading
space design
U-shaped platform with a volume of 25 m3
Towing device
The front and rear tow forks for a 52 mm diameter finger are mounted on the frame.
Curb weight, kg
18 800
Curb weight distribution, kg
first axle
4,850
second axis
4,950
third axis
4,500
fourth axis
4,500
Technically permissible maximum weight, kg
50 000*
Technically permissible maximum weight per axle, kg
first axle
9,000 (10,000**)
second axis
9,000 (10,000**)
third axis
16,000 (17,000**)
fourth axis
16,000 (17,000**)
Load capacity, kg
31 200*
* It is allowed to increase the load capacity to 35,200 kg with a corresponding increase in the technically permissible maximum weight to 54,000 kg, subject to a maximum speed limit of no more than 50 km/h.
** The mass per axle when the technically permissible maximum mass is increased to 54,000 kg.
Maximum driving speed, km/h, at least
85+4 (with speed limiter)
Reference fuel consumption when driving at a speed of 60 km/h (80 km/h), l/100 km
49.5 (61.0)

Dump trucks